Kia Stinger: ISG (Idle Stop & Go) System / Brake switch

Kia Stinger CK 2018-2024 Service Manual / Engine Control / Fuel System / ISG (Idle Stop & Go) System / Brake switch

Components and components location

Components

1. Brake switch

2. Brake pedal

Schematic diagrams

Terminal function

Pin No	Description
1	IGN1
2	IBU
3	-
4	B+
5	Stop lmap
6	Ground

Troubleshooting

Part diagnosis

Items

Cause

Symptom

Switch fuse

Faulty fuse connection, Damaged fuse

–	DTC Code : P0504

–	Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble, ESP OFF light illuminated.

① A waveform inspection is performed using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection procedures)

② Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)

Relay fuse

Faulty fuse connection, Damaged fuse

–	DTC Code : P0504

–	Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESP OFF light illuminated.

Stop lamp switch

•	Damaged wiring of each part

•	Faulty connection to connector

•	Each part is defective

–	DTC Code : P0504

–	Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESP OFF light illuminated.

Stop signal electronic
module (If it applies)

–	DTC Code : P0504, C2130, C2131

–	Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESP OFF light illuminated.

Engine control module(ECM)

–	DTC Code : P0504

–	Symptom :Shifting gear trouble,Cruise control function cancelation trouble

Body control module (BCM)

–	Shifting gear trouble

Shift-lock solenoid

–	Shifting gear trouble

Inhibitor switch

–	Symptom : Shifting gear trouble, Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble

Smart Key Unit(SMK)

–	Starting failure

Electronic parking brake

–	Symptom : EPB function cancelation trouble , ESP OFF light illuminated.

ABS/VDC control module
(Pressure sensor)

–	Symptom : ESP OFF light illuminated.

Symptom diagnosis

Symptom	Part that could be the cause
Trouble starting	Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ABS/VDC control module, Each wire, Connector	① Inspect waveform using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection Procedures) ② Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)
Trouble shifting gears	Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, BCM, ECM, Inhibitor switch, Each wire, Connector
ESP OFF light illuminated	Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ABS/VDC control module, Each wire, Connector
P0504	Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ECM, Each wire, Connector
Stop lamp not working	Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, Wire/Connector disconnected
Stop lamp always turned on	Stop lamp switch, Stop signal electronic module, Wiring short circuit, Damaged fuse

3.	Stop lamp switch system diagnosis SSEM : Stop Signal Electronic Module

4.	Refer to DTC guide when the related DTC codes are displayed.

Repair procedures

Removal

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel")

3.	Remove the knee airbag. (Refer to Restraint - "Knee airbag")

4.	Disconnect the brake lamp switch connector (A).

5.	Pull the locking plate (A) as indicated by the arrow and then turn brake switch (B) 45° clockwise and remove it.

Inspect a removed stop lamp switch along the below procedures.

(1)

Confirm a normal connection with terminal part.

–	A confirmation can be made to see if the connector has been secured properly and if a connection mark is present.

(2)	Perform the inspection of parts resistance.

Installation

1.	Fix the brake pedal arm and insert fully the brake switch so that the contact part is invisible.

2.	After inserting, turn the brake switch 45° counterclockwise, and then assemble locking plate by pushing.

Confirm the gap between stop lamp switch and bracket.

Stop lamp clearancee (A) :

1.0 - 2.0 mm (0.04 - 0.08 in.)

•	If the gap between stop lamp switch and bracket is not between 1.0 - 2.0 mm (0.04 - 0.08 in), check the mounting clip and other parts around the stop lamp.

•	If everything is normal, reinstall the stop lamp switch and check the clearance again.

4.	Install the stop lamp switch connector (A).

Starter

Specifications Specification Item Specification Rated voltage 12 V, 1.2 kW The number of pinion teeth ...

Door switch

Description and operation Description Via the seat belt/door switch, the ISG function can detect if the driver side seat belt is fastened and the driver side door is closed. If the dri ...

Other information:

Kia Stinger CK 2018-2024 Owners Manual: Power brakes

Your vehicle has power-assisted brakes that adjust automatically through normal usage. In the event that the power-assisted brakes lose power because of a stalled engine or some other reason, you can still stop your vehicle by applying greater force to the brake pedal than you normally would. ...

Kia Stinger CK 2018-2024 Service Manual: Pantoscopic Camera

Components and components location Components Front View Camera Side View Camera Rear View Camera Repair procedures Removal In case of bad quality or p ...