Kia Stinger: Brake System

Kia Stinger CK 2018-2024 Service Manual / Brake System

Special service tools
Special Service Tools

Tool Name / Number
Illustration
Description
Piston expander
09581-11000

Spreading the front disc brake piston

Brake bleeding procedures
Adjustment

Brake System Bleeding

  
•

Do not reuse the drained fluid.

•

Always use genuine DOT3/DOT4 brake fluid.

Using a non-genuine DOT3/DOT4 brake fluid can cause corrosion and decrease the life of the system.

•

Avoid contaminating the brake fluid by keeping it away from dirt or other foreign matters.

•

Do not spill brake fluid on the vehicle as it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.

•

The reservoir on the master cylinder must be at the MAX (upper) level mark at the start of bleeding procedure and checked after bleeding each brake caliper.

1.

Make sure that the brake fluid in the reservoir is filled upto the MAX (upper) level line.

2.

Have someone slowly pump the brake pedal several times, and then apply pressure.

3.

Loosen the rear right-hand side brake bleed screw (A) to allow air to escape from the system. Then tighten the bleed screw securely.

[Normal brake]

Front

Rear

[Brembo brake]

  

Let the inner (A) air bleeding and then let the outer (B) air when the procedure of air bleeding brembo brake air.

Front

Rear

4.

Repeat the procedure for all wheels in the sequence shown below until air bubbles no longer appear in the fluid.

[Normal brake]

[Brembo brake]

5.

Refill the master cylinder reservoir upto the MAX (upper) level line.

  

Do not reuse the old brake fluid. Use only new clean brake fluid.

ESP Bleeding of Brake System

Follow this procedure to ensure adequate bleeding of air and filling of the ESP unit, brake lines and master cylinder with brake fluid.

1.

Remove the reservoir cap and fill the brake reservoir with brake fluid.

  
•

If there is any brake fluid on any painted surface, wash it off immediately.

  
•

When pressure bleeding, do not depress the brake pedal.

•

Recommended fluid: DOT3 or DOT4

2.

Connect a clear plastic tube to the wheel cylinder bleeder plug and insert the other end of the tube into a half filled clear plastic bottle.

3.

Connect the KDS to the data link connector located underneath the dash panel.

4.

Select and operate according to the instructions on the KDS screen.

  
•

Comply with the maximum operating time of the ESP motor on the KDS to prevent the motor pump from burning.

(1)

Select vehicle name.

(2)

Select ABS/ESP system.

(3)

Select HCU air bleeding mode.

5.

Pump the brake pedal several times, and then loosen the bleeder screw until fluid starts to run out without bubbles. Then close the bleeder screw (A).

[Normal brake]

Front

Rear

[Brembo brake]

  

Let the inner (A) air bleeding and then let the outer (B) air when the procedure of air bleeding brembo brake air.

Front

Rear

6.

Repeat step 5 in the order shown below until there are no more bubbles in the fluid for each wheel.

[Normal brake]

[Brembo brake]

7.

Tighten the bleeder screw.

Bleed screw tightening torque:

17 in : 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft)

18 in : 16.7 - 19.6 N·m (1.7 - 2.0 kgf·m, 12.3 - 14.4 lb·ft)

Troubleshooting
Troubleshooting
Problem Symptoms Table

Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.

Check each part in order.

If necessary, replace these parts.

Symptom
Expected cause
Countermeasure
Lower pedal or sponge pedal
Brake system (oil leakage)
Repair
Brake system (air inflow)
Air bleeding out procedure
Piston seal (worn out or damaged)
Replace
Rear brake shoe separation (faulty adjustment)
Adjust
Master cylinder (malfunction)
Replace
Dragged brake
Brake pedal free separation (minimum)
Adjust
Parking brake cable length (adjustment trouble)
Adjust
Parking brake cable (trapped)
Repair
Rear brake shoe separation (adjustment trouble)
Adjust
Pad and lining (twisted or cracked)
Replace
Piston (trapped)
Replace
Piston (frozen)
Replace
Anker or return spring (malfunction)
Replace
Booster system (leakage of vacuum)
Repair
Master cylinder (malfunction)
Replace
Uneven brake
Piston (trapped)
Replace
Pad and lining (oil stain, cracked or twisted)
Replace
Heavy pedal and brake trouble
Brake system (oil leakage, air inflow)
Perform air bleeding procedure
Pad or lining (worned out)
Replace
Pad or lining (cracked or twisted)
Replace
Rear brake shoe separation (adjustment trouble)
Adjust
Pad or lining (oil stain)
Replace
Pad or lining (slippery)
Replace
Disc (scratched)
Replace
Booster system (leakage of vacuum)
Repair
Noise from brake
Pad or lining (cracked or twisted)
Replace
Looseness of wheel bolt and caliper
Adjust
Pad sliding trouble (Pad uneven worn out)
Replace
Pad or lining (dirty)
Cleaning
Pad or lining (slippery)
Pad replacement
Anker or return spring (malfunction)
Replace
Brake pad shim (damaged)
Replace
Hold down spring (damaged)
Replace
Foreign substance stucked between disc and pad
Cleaning
Corrosion on disc
Test drive brake and cleaning
* get rid of corrosion by friction while test drive brake
Caved disc
Replace
Not fully functioning on brake
(when drive speed is fast)
Pad or lining (worned out)
Replace
Master cylinder (malfunction)
Replace
Brake vibration
Brake booster (leakage of vacuum)
Repair
Pedal free separation
Adjust
Master cylinder (malfunction)
Replace
Damaged on master cylinder cap
Replace
Damaged on brake line
Replace
Caliper returning trouble (while tire is turning, check the noise)
Replace
Transformed disc
Replace

Active hood actuator assembly
Repair procedures Replacement 1. Disconnect the negative battery terminal.    ...

Specifications
Service data Service data Item Specification Master cylinder Type Tandem Cylinder I.D. Ã ...

Other information:

Kia Stinger CK 2018-2024 Owners Manual: Sliding the sunroof


When the sunshade is closed Pull the sunroof control lever backward to the 2nd detent position, and both the sunshade and sunroof glass will slide all the way open. When the sunshade is opened Pull the sunroof control lever back ward to the 1st or 2nd detent position, the sunroof glass will ...

Kia Stinger CK 2018-2024 Service Manual: Roller Blind


Components and components location Components Location 1. Roller assembly Repair procedures Replacement    Put on gloves to protect your hands. ...

Copyright © www.kstinger.com 2015-2024