Kia Stinger: Exhaust Emission Control System / Catalytic Converter

Kia Stinger CK 2018-2024 Service Manual / Emission Control System / Exhaust Emission Control System / Catalytic Converter

Description and operation

Description

The catalytic converter of the gasoline engine is a three way catalyst. It oxidizes carbon monoxide and hydrocarbons (HC), and separates oxygen from the oxides of nitrogen (NOx).

Catalytic Converter (WCC)

Repair procedures

Removal

1.	Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")

2.	Disconnect the negative battery terminal.

3.	Remove the engine room front under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")

4.	Drain the coolant. (Refer to Engine Mechanical System - "Coolant")

5.	Remove the air intake hose. (Refer to Engine Mechanical System - "Air Cleaner")

6.	Disconnect the recirculation valve connector (A) and the vacuum hose (B).

Remove the intercooler inlet hose & pipe assembly (A).

Tightening torque

Nuts (B) :

14,7 - 19.6 N·m (1.5 - 2.0 kgf·m, 10.8 - 14.5 lb·ft)

Nut (C) :

14.7 - 19.6 N·m (1.5 - 2.0 kgf·m, 10.8 - 14.5 lb·ft)

1)	When disconnect the intercooler inlet hose, pull out the quick connector clamp (A) in the direction of the arrow as shown below.

2)	Move the quick connector clamp from position (B) to position (C) as shown below and pull out the quick connector hose.

Remove the turbocharger inlet hose (A).

Tightening torque :

4.9 - 6.9 N·m (0.5 - 0.7 kgf·m, 3.6 - 5.1 lb·ft. 43.4 - 60.8 lb·in)

Remove the heat protector (A).

Tightening torque :

7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

10.	Remove the heated oxygen sensor. (Refer to Engine Control / Fuel System - " Heated Oxygen Sensor ( HO2S)")

11.

Remove the warm-up catalytic converter (WCC) heat protector (A).

Tightening torque :

18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)

12.	Remove the front muffler. (Refer to Engine Mechanical System - "Muffler")

13.

Remove the warm-up catalytic converter (WCC) stay (A).

Tightening torque

Bolts (B) :

18.6 - 27.5 N·m (1.9 - 2.8 kgf·m, 13.7 - 20.3 lb·ft)

Bolts (C) :

52.0 - 57.9 N·m (5.3 - 5.9 kgf·m, 38.3 - 42.7 lb·ft)

14.	Remove the RH hood sealing cover (A).

15.	Disconnect the heater hose (A).

16.

Remove the warm-up catalytic converter (WCC) (A) and gasket.

Tightening torque :

49.0 - 53.9 N·m (5.0 - 5.5 kgf·m, 36.2 - 39.7 lb·ft)

Installation

1.	Install in the reverse order of removal.

Exhaust Emission Control System

Description and operation Description Exhaust emissions (CO, HC, NOx) are controlled by a combination of engine modifications and the addition of special control components. Modifica ...

CVVT (Continuous Variable Valve Timing) System

Description and operation Description Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valve in accordance with the ECM con ...

Other information:

Kia Stinger CK 2018-2024 Owners Manual: Closing the fuel filler lid

1. To install the cap, turn it clockwise until it “clicks” once. This indicates that the cap is securely tightened. 2. Close the fuel filler lid and push it in lightly making sure that it is securely closed. ✽ NOTICE There may be an intermittent noise near the refueling hole while the e ...

Kia Stinger CK 2018-2024 Service Manual: Windshield Glass

Components and components location Components 1. Windshield glass 2. Windshield molding mounting bracket 3. Windshield glass side molding 4. Windshield glass upper molding Repair procedures Removal ...