Kia Stinger: Engine Control System / Exhaust Gas Temperature Sensor (EGTS)

Kia Stinger CK 2018-2024 Service Manual / Engine Control / Fuel System / Engine Control System / Exhaust Gas Temperature Sensor (EGTS)

Specifications

Specification

Exhaust Gas Temperature Sensor (EGTS) #1, 2

▷ Type : Thermistor type

Temperature [°C (°F)]	Resistance (kΩ)
-40 (-40)	0.17
0 (-32)	0.201
100 (212)	0.276
200 (392)	0.35
300 (572)	0.42
400 (752)	0.489
500 (932)	0.555
600 (1112)	0.618
700 (1292)	0.68
800 (1472)	0.739
850 (1562)	0.767

Description and operation

Description

Installed in exhaust manifold, the Exhaust Gas Temperature Sensor (EGTS) #1 for WGT senses the temperature of exhaust gas flowing into the WGT.

Installed in Gasoline Particulate Filter (GPF) assembly, the Exhaust Gas Temperature Sensor (EGTS) #2 for GPF senses the temperature of exhaust gas flowing into the GPF.

When predetermined engine condition is met, ECM burns soot collected in GPF with exhaust gas. During this, the exhaust gas temperature is an important factor of engine condition.

Schematic diagrams

Circuit Diagram

EGTS #1

Harness Connector

EGTS #2

Harness Connector

EGTS #3

Repair procedures

Inspection

1.	Turn ignition switch OFF.

2.	Disconnect the connector of exhaust gas temperature sensors #1/#2/#3.

3.	Measure resistance between sensor signal terminal and ground terminal.

Check that the resistance is within the specification.

Exhaust Gas Temperature Sensor [EGTS #1, #2, #3 (T3, T4, T5)]

Temperature [°C (°F)]	Resistance (kΩ)
-40 (-40)	0.17
0 (-32)	0.201
100 (212)	0.276
200 (392)	0.35
300 (572)	0.42
400 (752)	0.489
500 (932)	0.555
600 (1112)	0.618
700 (1292)	0.68
800 (1472)	0.739
850 (1562)	0.767

Removal & Installation

[EGTS #1]

1.	Turn the ignition switch OFF and disconnect the battery negative (-) terminal.

2.	Remove the floor under cover.

3.	Disconnect the EGTS connector (A).

Remove the EGTS (A).

Exhaust gas temperature sensor (EGTS) :

39.2 - 49.1 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Install the sensor in the reverse order of removal.

•	Install the sensor with the specified torque.

•	If the sensor is dropped by mistake, check if there is no problem.

[EGTS #2]

1.	Turn the ignition switch OFF and disconnect the battery negative (-) terminal.

2.	Remove the floor under cover.

3.	Disconnect the EGTS connector (A).

Remove the EGTS (A).

Exhaust gas temperature sensor (EGTS) :

39.2 - 49.1 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Install the sensor in the reverse order of removal.

•	Install the sensor with the specified torque.

•	If the sensor is dropped by mistake, check if there is no problem.

[EGTS #3]

1.	Turn the ignition switch OFF and disconnect the battery negative (-) terminal.

2.	Remove the floor under cover.

3.	Disconnect the EGTS connector (A).

Remove the EGTS (A).

Exhaust gas temperature sensor (EGTS) :

39.2 - 49.1 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Install the sensor in the reverse order of removal.

•	Install the sensor with the specified torque.

•	If the sensor is dropped by mistake, check if there is no problem.

Heated Oxygen Sensor (HO2S)

Specifications Specification HO2S [Bank 1/Sensor 1] Item Specification Heater Resistance (Ω) 2.5 - 4.0 [20°C(68°F)] ...

Rail Pressure Sensor (RPS)

Specifications Specification Pressure Output Voltage (V) [Vref=5V] bar [MPa (kgf/cm², psi)] 0 0 (0, ...

Other information:

Kia Stinger CK 2018-2024 Owners Manual: 360° camera monitoring system

The 360° camera monitoring system is not a substitute for proper and safe parking procedures. The 360° camera monitoring system may not detect every object surrounding the vehicle. Always drive safely and use caution when parking. The 360° camera monitoring system can assist in parking by ...

Kia Stinger CK 2018-2024 Service Manual: Mechanism Assembly

Repair procedures Replacement Put on gloves to protect your hands. • Use a plastic panel removal tool to remov ...