Kia Stinger: Brake System / Master Cylinder

Kia Stinger CK 2018-2024 Service Manual / Brake System / Brake System / Master Cylinder

Components and components location

Components

1. Master cylinder
2. Brake booster

3. Brake reservoir

Repair procedures

Removal

[LHD]

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

Remove the brake fluid from the master cylinder reservoir with a syringe.

Do not spill brake fluid on the vehicle as it may damage the paint. If brake fluid comes in contact with the paint, wash off immediately with water.

3.	Remove the hood sealing cover.

Remove the engine control module (ECM).

D 2.2 R VGT (Refer to Engine Control /Fuel System - "Engine Control Module (ECM)")

D 2.2 R VGT (Enhanced Euro 6) (Refer to Engine Control /Fuel System - "Engine Control Module (ECM)")

G 2.0 T-GDI (Refer to Engine Control /Fuel System - "Engine Control Module (ECM)")

G 3.3 T-GDI (Refer to Engine Control /Fuel System - "Engine Control Module (ECM)")

5.	Disconnect the brake fluid level sensor connector.

Loosen the master cylinder flare nuts.

Tightening torque:

18.6 - 22.5 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)

Remove the master cylinder from the brake booster after loosening the mounting nuts.

Tightening torque:

12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)

[RHD]

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

Remove the brake fluid from the master cylinder reservoir with a syringe.

Do not spill brake fluid on the vehicle as it may damage the paint. If brake fluid comes in contact with the paint, wash off immediately with water.

3.	Remove the RH hood sealing cover (A).

4.	Disconnect the wirings (A) from the joint junction block.

Detach the joint junction block (B).

Tightening torque:

10.8 - 13.7 N·m (1.1 - 1.4 kgf·m, 8.0 - 10.1 lb·ft)

6.	Disconnect the brake fluid level sensor connector (A).

Loosen the master cylinder flare nuts (B).

Tightening torque:

18.6 - 22.5 N·m (1.9 - 2.3 kgf·m, 13.7 - 16.6 lb·ft)

Remove the master cylinder (A) from the brake booster after loosening the mounting nuts.

Tightening torque:

12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)

Installation

1.	Install in the reverse order of removal.

2.	After installation, bleed the brake system. (Refer to Brake system - "Brake Bleeding Procedures")

Vacuum Pump

Components and components location Components 3.3 T-GDI LAMBDA II 1. Vacuum pump 2. Vacuum pump bracket 2.0 T-GDI THETA II ...

Brake Line

Components and components location Components Repair procedures Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. ...

Other information:

Kia Stinger CK 2018-2024 Service Manual: Pillar Garnish

Repair procedures Replacement • Use a plastic panel removal tool to remove interior trim pieces without marring the surface. • Take care not ...

Kia Stinger CK 2018-2024 Owners Manual: FCA warning message and system control

The FCA system produces warning messages, warning alarms, and emergency braking based on the level of risk of a frontal collision, such as when a vehicle ahead suddenly brakes, or when the system detects that a collision with a pedestrian is imminent. Collision Warning (1st warning) The ...