Kia Stinger: Power Door Locks / Power Door Lock Module
Components and components location
1. Door lock/unlock knob cable
2. Door inside handle cable
|
3. Door latch assembly
|
Repair procedures
• |
When removing with a flat-tip screwdriver or remover, wrap protective
tape around the tools to prevent damage to components.
|
• |
When removing the interior trim pieces, use a plastic panel removal
tool not to damage the surface.
|
• |
Be careful to store and handle the trim when removing/installing
because lubricant and oil can leave a stain on the trim.
|
|
Front Door Lock Module
Inspection
1. |
Remove the front door trim.
(Refer to Body - "Front Door Trim")
|
2. |
Remove the front door module.
(Refer to Body - "Front Door Module")
|
3. |
Disconnect the connector from the actuator.
[Central Lock]
No.
|
Pin Information
|
LH
|
RH
|
1
|
-
|
AJAR switch
|
2
|
Motor 1
|
COM
|
3
|
Motor 2
|
Lock / Unlock switch
|
4
|
-
|
-
|
5
|
-
|
-
|
6
|
Lock / Unlock switch
|
Motor 2
|
7
|
COM
|
Motor 1
|
8
|
AJAR switch
|
-
|
[Dead Lock]
No.
|
Pin Information
|
LH
|
RH
|
1
|
Motor 1
|
AJAR switch
|
2
|
Motor 2
|
COM
|
3
|
Motor 3
|
Lock / Unlock switch
|
4
|
Key unlock switch
|
Key lock switch
|
5
|
Key lock switch
|
Key unlock switch
|
6
|
Lock / Unlock switch
|
Motor 3
|
7
|
COM
|
Motor 2
|
8
|
AJAR switch
|
Motor 1
|
|
4. |
Check actuator operation by connecting power and ground as shown below.
To prevent damage to the actuator, apply battery voltage only momentarily.
[Central Lock
(Without key switch)]
[Dead Lock
(Without Key Switch)]
[Dead Lock
(With Key Switch)]
[Central Lock]
[Dead Lock]
|
Rear Door Lock Module
Inspection
1. |
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
|
2. |
Remove the rear door module.
(Refer to Body - "Rear Door Module")
|
3. |
Disconnect the connector from the actuator.
[Central Lock]
No.
|
Pin Information
|
LH
|
RH
|
1
|
-
|
AJAR switch
|
2
|
Motor 1
|
COM
|
3
|
Motor 2
|
Lock / Unlock switch
|
4
|
-
|
-
|
5
|
-
|
-
|
6
|
Lock / Unlock switch
|
Motor 2
|
7
|
COM
|
Motor 1
|
8
|
AJAR switch
|
-
|
[Dead Lock]
No.
|
Pin Information
|
LH
|
RH
|
1
|
Motor 1
|
AJAR switch
|
2
|
Motor 2
|
COM
|
3
|
Motor 3
|
Lock / Unlock switch
|
4
|
-
|
-
|
5
|
-
|
-
|
6
|
Lock / Unlock switch
|
Motor 3
|
7
|
COM
|
Motor 2
|
8
|
AJAR switch
|
Motor 1
|
|
4. |
Check actuator operation by connecting power and ground as shown below.
To prevent damage to the actuator, apply battery voltage only momentarily.
[Central Lock
(Without key switch)]
[Dead Lock
(Without Key Switch)]
[Central Lock]
[Dead Lock]
|
Tailgate Lock Module
Inspection
1. |
Remove the tailgate trim.
(Refer to Body - "Tailgate Trim")
|
2. |
Disconnect the connectors from the actuator.
|
3. |
Check actuator operation by connecting power and ground as shown below.
To prevent damage to the actuator, apply battery voltage only momentarily.
|
4. |
Checking the tailgate of the vehicle power option power refers to the
tailgate module.
|
Components and components location
Component Location
1. Driver power window switch
2. Assist power window switch
3 . Integrated central control unit (ICU)
4 ...
Repair procedures
Inspection
Diagnosis With KDS
1.
The body electrical system can be quickly diagnosed for failed parts
by using vehicle diagnostic system (KDS).
Th ...
Other information:
The rear view monitor will activate with the ignition switch ON, engine ON and
the shift lever in the R (Reverse) position. This system is a supplemental system
that shows the area behind the vehicle on the audio screen while backing up. If
the vehicle is equipped with a navigation system, t ...
Repair procedures
Removal and Installation
Removal of the thermostat would have an adverse effect, causing a lowering
of cooling efficiency. Do not remove the thermostat, even if the engine
tends to overheat. ...