Kia Stinger: Power Tailgate System / Power Tailgate Module

Kia Stinger CK 2018-2024 Service Manual / Body Electrical System / Power Tailgate System / Power Tailgate Module

Components and components location
Components

No.
Connector A
Connector B
Connector C
1
Power supply
Cinching motor (+)
Spindle motor (RH)_Close (-)
2
Illumination (Tailgate inner switch)
Tailgate full open switch
Hall sensor (RH)_Power
3
-
Tailgate full lock switch
Spindle (LH) shild_Ground
4
B-CAN (High)
Tailgate half lock switch
Hall sensor (RH)_Ground
5
B-CAN (Low)
Home position switch_Ground
Spindle (RH) shild_Ground
6
Buzzer
Tailgate latch switch _Ground
Hall sensor (LH)_Power
7
-
System ground
Spindle motor (LH)_Close (+)
8
Tailgate motor
Cinching motor (-)
Spindle motor (RH)_Close (+)
9
-
Tailgate open/close switch
Hall sensor 1 (RH)
10
Gear 'N' Position
Tailgate inner switch
Hall sensor 2 (RH)
11
-
Home position switch
Hall sensor (LH)_Ground
12
Antipinch strip (LH)_Power
Antipinch strip (LH)_Ground
Hall sensor 1 (LH)
13
Antipinch strip (RH)_Power
Antipinch strip (RH)_Ground
Hall sensor 2 (LH)
14
-
Power ground
Spindle motor (LH)_Close (-)

Schematic diagrams
Circuit Diagram

Repair procedures
Removal
  
a.

After replacing with a new power tailgate module, check for DTC code at all times.

If DTC code B24B0 exists, perform power tailgate mode change.

(Refer to Power Tailgate System - "Troubleshooting")

b.

After replacing with a new power tailgate module, perform the system initialization.

(Refer to Power Tailgate System - "Troubleshooting")

c.

Before delivery to customer, operate the power tailgate to be sure that there is no warning sound.

1.

Disconnect the negative (-) battery terminal.

2.

Remove the luggage side trim [LH].

(Refer to Body - "Luggage Side Trim")

3.

Disconnect the power tailgate module connectors (A).

4.

Remove the power tailgate module (A) after loosening the mounting nuts.

Installation
1.

Install the power tailgate module.

2.

Connect the power tailgate module connectors.

3.

Install the luggage side trim [LH].

4.

Connect the negative (-) battery terminal.

Inspection

Inspection of the Power Tailgate Module

Refer to Power Tailgate System - "Troubleshooting"

Power Tailgate System
Components and components location Components 1. Anti pinch strip (2EA) 2. Power tailgate spindle (2EA) 3. Power tailgate buzzer 4. Side crash pad switch 5. ...

Power Tailgate Latch
Repair procedures Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the tailgate trim. (Refer to Body - "Tailgate Trim" ...

Other information:

Kia Stinger CK 2018-2024 Service Manual: SRS Control Module (SRSCM)


Description and operation Description The primary purpose of the SRSCM (Supplemental Restraints System Control Module) is to discriminate between an event that warrants restraint system deployment and an event that does not. The SRSCM must decide whether to deploy the restraint sys ...

Kia Stinger CK 2018-2024 Service Manual: Smart Cruise Control (Stop & Go) (SCC) Switch


Components and components location Components 1. Left Remote Control Switch (Audio + Bluetooth + Voice) 2. Right Remote Control Switch (Trip Computer + ACC + SCC) Schematic diagrams Circuit Diagram [Audio + Blueto ...

Copyright © www.kstinger.com 2015-2024