Kia Stinger Manuals

Kia Stinger: Driveshaft and axle / Rear Driveshaft Assembly

Kia Stinger CK 2018-2024 Service Manual / Driveshaft and axle / Rear Driveshaft Assembly

Repair procedures
Removal
1.

Remove wheel nuts, wheel and tire (A) from hub.

Tightening torque:

107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

  

Be careful not to damage the wheel nuts when removing the wheel and tire (A).
2.

Remove the rear brake caliper.

(Refer to Brake System - "Rear Disc Brake")

3.

Remove the split pin (A) from the rear hub and loosen the hub nut (B).

4.

Remove the rear lower arm cover (A).
5.

Remove the wheel speed sensor.

Tightening torque :

6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 7.9 lb·ft)

6.

Loosen the stabilizer link nut and then separate the rear axle.

Tightening torque :

98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

  

Up the transmission jack under the lower arm in order to remove the stabilizer link in no-load condition.
7.

Loosen the rear lower arm bolt & nut and then separate the rear lower arm from the rear axle.

Tightening torque :

156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

8.

Loosen the nut & bolt and then separate the trailing arm from the rear axle.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

9.

Loosen the bolt (A) and then separate the rear assist arm from the rear axle.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

10.

Loosen the bolt & nut and then remove the rear upper arm front from the rear axle.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

11.

Loosen the rear upper arm rear bolt & nut (A) and then separate the rear upper arm rear.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

12.

Separate the rear drive shaft from the knuckle.
13.

Using pry bar, remove the rear drive shaft from the rear differential.
14.

Install in the reverse order of removal.
BJ Boot
Repair procedures Replacement 1. Remove the front driveshaft. (Refer to Driveshaft Assembly - “Front Driveshaft”) 2. Remove the TJ joint as ...

Propeller Shaft Assembly
...

Other information:

Kia Stinger CK 2018-2024 Service Manual: Blind-Spot Collision Warning (BCW)


Specifications Specifications Items Specification Rated voltage DC 12 V Operating voltage 9 - 16 V Operating speed 30 - 255 km/h Sensing distance ...

Kia Stinger CK 2018-2024 Service Manual: Smart Key Diagnostic


Repair procedures Inspection 1. In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (KDS). The diagnostic system (KDS) provides the following information. (1) Self diagnosis : Checking ...

Copyright © www.kstinger.com 2015-2024