Kia Stinger: Rear Suspension System / Rear Stabilizer Bar
Repair procedures
1. |
Remove wheel nuts, wheel and tire (A) from hub.
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)
|
Be careful not to damage the wheel bolts when removing the wheel
and tire (A).
|
|
2. |
Remove the brake caliper.
(Refer to Brake system - "Rear disc brake")
|
3. |
Loosen the stabilizer link nut and then separate the rear axle.
Tightening torque:
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
|
|
4. |
Loosen the rear shock absorber upper bolts and the remove the rear shock
absorber.
Tightening torque :
63.7 - 78.4 N·m (6.5 - 8.0 kgf·m, 47.0 - 57.9 lb·ft)
|
Up the transmission jack under the lower arm in order to remove
the rear shock absorber in no-load condition.
|
|
5. |
Remove the propeller shaft.
(Refer to Driveshaft and axle - "Propeller shaft")
|
6. |
Remove the rear muffler.
D 2.2 R VGT (Refer to Engine Mechanical System - "Muffler")
G 2.0 T-GDI THETA II (Refer to Engine Mechanical System - "Muffler")
G 3.3 T-GDI LAMBDA II (Refer to Engine Mechanical System - "Muffler")
|
7. |
Loosen the rear cross member nuts & bolts and then remove the rear cross
member.
Tightening torque :
(A,C) : 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)
(B) : 44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)
|
|
8. |
Loosen the stabilizer bar nuts & bolts and then remove the stabilizer
bar.
Tightening torque :
49.0 - 63.7 N·m (5.0 - 6.5 kgf·m, 36.2 - 47.0 lb·ft)
|
|
9. |
Install in the reverse order of removal.
|
10. |
Check the alignment.
(Refer to Suspension System - "Alignment")
|
1. |
Check the rear stabilizer bar for deformation.
|
2. |
Check the rear stabilizer link ball joint for damage.
|
Repair procedures
Removal
1.
Remove wheel nuts, wheel and tire (A) from hub.
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 9 ...
Repair procedures
Removal
1.
Remove wheel nuts, wheel and tire (A) from hub.
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94. ...
Other information:
Adjust the rearview mirror so that the center view through the rear window is
seen. Make this adjustment before you start driving.
Do not place objects in the rear seat or cargo area which would interfere with
your vision through the rear window.
WARNING - Mirror adjustment
Do not adjust the ...
Components and components location
Component Location
1. Rear back side seat assembly
[LH]
2. Rear seat back assembly [LH]
3. Rear seat back assembly [RH]
4. Rear back side seat assembly [RH]
Repair procedures
Replacement
...