Kia Stinger: Rear Suspension System / Rear Upper Arm

Kia Stinger CK 2018-2024 Service Manual / Suspension System / Rear Suspension System / Rear Upper Arm

Repair procedures

Removal

[Rear upper arm rear]

Remove wheel nuts, wheel and tire (A) from hub.

Tightening torque:

107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Be careful not to damage the wheel bolts when removing the wheel and tire (A).

Loosen the rear upper arm bolt & nut and then separate the rear upper arm rear from the rear axle.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

Up the transmission jack under the lower arm in order to remove the rear upper arm in no-load condition.

Loosen the upper arm rear bolt and then remove the rear upper arm.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

Install in the reverse order of removal.

Install at the empty vehicle height when it is assembled.

[Rear upper arm front]

Remove wheel nuts, wheel and tire (A) from hub.

Tightening torque:

107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Be careful not to damage the wheel bolts when removing the wheel and tire (A).

2.	Remove the brake caliper. (Refer to Brake system - "Rear disc brake")

3.	Disconnect the EPB connector (A).

Loosen the stabilizer link nut and then separate the rear axle.

Tightening torque :

98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Loosen the rear upper front bolt & nut from the rear axle.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

Loosen the rear shock absorber upper bolts and the remove the rear shock absorber.

Tightening torque :

63.7 - 78.4 N·m (6.5 - 8.0 kgf·m, 47.0 - 57.9 lb·ft)

7.	Remove the propeller shaft. (Refer to Driveshaft and axle - "Propeller shaft")

8.	Remove the rear muffler. D 2.2 R VGT (Refer to Engine Mechanical System - "Muffler") G 2.0 T-GDI THETA II (Refer to Engine Mechanical System - "Muffler") G 3.3 T-GDI LAMBDA II (Refer to Engine Mechanical System - "Muffler")

Loosen the rear cross member nuts & bolts and then remove the rear cross member.

Tightening torque :

(A,C) : 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)

(B) : 44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

10.

Loosen the rear upper arm front nut & bolt and then remove the rear upper arm front from the rear cross member.

Tightening torque :

117.7 - 132.4 N·m (12.0 - 13.5 kgf·m, 86.8 - 97.6 lb·ft)

11.

Install in the reverse order of removal.

Install at the empty vehicle height when it is assembled.

12.	Check the alignment. (Refer to Suspension System - "Alignment")

Inspection

1.	Check the bushing for wear and deterioration.

2.	Check the ball joint for rotating torque.

Rear Shock Absorber

Components and components location Components 1. Lock nut 2. Rear insulator 3. Bumper stopper 4. Dust cover 5. Shock absorber Repair procedu ...

Rear Assist Arm

Repair procedures Removal 1. Remove wheel nuts, wheel and tire (A) from hub. Tightening torque: 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94. ...

Other information:

Kia Stinger CK 2018-2024 Service Manual: Cylinder Head

Repair procedures Removal In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do ...

Kia Stinger CK 2018-2024 Service Manual: Engine Oil and Filter

Repair procedures Inspection [Theta-II 2.0 T-GDI / Lambda-II 3.3 T-GDI] Engine Oil Level Be sure that the vehicle is on level ground. 1. Warm up and stop the engine, and then wait for 5 mi ...