Kia Stinger CK: Heating, Ventilation And Air Conditioning

Kia Stinger (CK) 2018-2023 Service Manual / Heating, Ventilation And Air Conditioning

Contents:

Special service tools

Special Service Tools

Tool (Number and name)	Illustration	Use
09977-3R000 Disc & hub assembly bolt remover		Removal and installation of disc & hub assembly.

Troubleshooting

Problem Symptoms Table

Before replacing or repairing air conditioning components, first determine if the malfunction is due to lack of refrigerant, air flow or compressor.

Use the following table to find the cause of the problem. The numbers indicate the order of the likely cause of the problem. Check each part in order. If necessary, replace the corresponding parts.

After fixing the area of malfunction, check the complete system to ensure satisfactory performance.

Standard:

Symptom	Suspected Area
No blower operation	1. Blower fuse
	2. Blower relay
	3. Blower motor
	4. Power mosfet
	5. Blower speed control switch
	6. Wire harness
No air temperature control	1. Engine coolant capacity
	2. Heater control assembly
	3. Temperature control actuator
No compressor operation	1. Refrigerant capacity
	2. A/C fuse
	3. Pulley assembly limiter
	4. Compressor
	5. A/C pressure transducer
	6. A/C switch
	7. Evaporator temperature sensor
	8. Wire harness
Vented air not cold	1. Refrigerant capacity
	2. Refrigerant pressure
	3. Drive belt
	4. Pulley assembly limiter
	5. Compressor
	6. A/C pressure transducer
	7. Evaporator temperature sensor
	8. A/C switch
	9. Heater control assembly
	10. Wire harness
Insufficient cooling	1. Refrigerant capacity
	2. Drive belt
	3. Pulley assembly limiter
	4. Compressor
	5. Condenser
	6. Expansion valve
	7. Evaporator
	8. Refrigerant lines
	9. A/C pressure transducer
	10. Heater control assembly
No engine idle-up when A/C switch ON	1. Engine ECM
No engine idle-up when A/C switch ON	2. Wire harness
No air inlet control	1. Heater control assembly
No mode control	1. Heater control assembly
No mode control	2. Mode actuator
No cooling fan operation	1. Cooling fan fuse
	2. Fan motor
	3. Engine ECM
	4. Wire harness

Other information:

Kia Stinger (CK) 2018-2023 Service Manual: Forward Collision-avoidance Assist (FCA)

The FCA system (if equipped) is designed to detect and monitor a vehicle ahead or detect a pedestrian in the roadway through radar signals and camera recognition to warn the driver that a collision is imminent, and if necessary, apply emergency braking. WARNING - Forward Collision-Avoidance assist (FCA) Limitations The FCA system is a supplemental system and is not a substitute for safe driving practices.

Kia Stinger (CK) 2018-2023 Service Manual: Rail Pressure Sensor (RPS)

Specifications Specification Pressure Output Voltage (V) [Vref=5V] bar [MPa (kgf/cm², psi)] 0 0 (0, 0) 0.5 140 14 (142, 2031) 2.5 280 28 (286, 4061) 4.5 Description and operation Description Installed on the delivery pipe, the Rail Pressure Sensor (RPS) measures the instantaneous fuel pressure in the delivery pipe.

Kia Stinger CK: Heating, Ventilation And Air Conditioning

Special service tools

Troubleshooting

Specifications ➤

Air Conditioning System ➤

Blower ➤

Controller ➤

Heater ➤

Wireless Power Charging (WPC) Lamp

Specifications

Other information:

Categories

Contents